Home | Products | CompactPCI boards | Analog I/O - Counter

Multifunction board, optically isolated,
16 SE or 8 diff. inputs, 4 analog outputs, 16-bit

CPCI-3009

The board CPCI-3009 is a fast multifunction and counter board for the CompactPCI bus.

It is characterised by flexible applications, high accuracy, speed and reliability in severe industrial environments.

With this board you can put into practice a large range of applications on the same hardware basis thanks to FPGA technology. The board is supplied with a pool of functionalities allowing a high efficiency on just one board. The functions are programmed using the supplied software. You can adapt the functions of the board to the requirements of your application and change them as required. On request, further counter applications can be adapted per software thanks to the the FPGA.

CompactPCI 3.3 V or 5 V
Can be inserted in PXI systems, with restricted
functionalities

Analog inputs

16 diff. inputs, optically isolated 1000 V
Resolution: 16-bit
Throughput: 200 kHz
Voltage inputs: 0-10 V, ±10 V, 0-5 V, ±5 V, 0-2 V, ±2 V,
0-1 V, ±1 V, 0-20 mA (option) freely programmable through software for each channel
Gain PGA x1, x2, x5, x10 freely programmable through software for each channel

Analog acquisition

Different input modes for the analog acquisition:
1) Simple mode
2) Scan modes
3) Sequence modes
4) Auto Refresh mode
Onboard FIFO
PCI-DMA for analog data acquisition

Analog outputs

4 analog outputs, optically isolated
12-bit resolution, setup time 15 µs typ
Output voltage after reset: 0 V
Each output has its own ground line
(without optical isolation)
Output voltage range: - 10 V up to + 10 V
Output current: ± 5 mA
Short-circuit current: ± 20 mA

24 V digital I/O

4 digital inputs, 24 V, optically isolated
4 digital outputs, 24 V, optically isolated

Reprogrammable counter function module

32-bit data access
Counter component with 32-bit width and 5 MHz counting frequency, signals in RS422 mode

Functions:

Incremental counter for the acquisition of incremental encoders (90° phase-shifted signals)
Chronos for frequency , pulse width and period duration measurement
Digital inputs and outputs, 24 V, TTL, RS422
Further functions on request:
SSI synchronous serial Interfaces. The SSI function is an interface for systems which allow an absolute position information via serial data transfer.
Counter/timer (82x54)
pulse acquisition
velocity measurement
PWM (Pulse Width Modulation)
Customized functions

Timer/Counter/Watchdog

3 / 3 / 2, 16-bit

Safety features

Optical isolation 1000 V min.
Creeping distance IEC 61010-1
Circuit part of the analog acquisition
is separated from the circuit part of the digital function
Overvoltage protection ± 40 V
Protection against high-frequency EMI
Input filters
Noise neutralization of the PC supply
Connection of the I/O-signals via robust industrystandard SUB-D connector

Ordering Information

CPCI-3009

Multifunction board, optically isolated, 16 SE or 8 diff. inputs, 4 analog outputs, 16-bit.

Incl. technical description and software drivers.

Options

URS-3009-6U: 6U front bracket for mounting in 6U housing

OPT.SF: Precision filter for 1 SE-channel

OPT.DF: Precision filter for 1 diff. channel, (30 Hz)
OPT.PC-SE: Current input 0(4)-20 mA for 1 SE-channel

OPT. PC-DIFF: Current input 0(4)-20 mA for 1 diff. channel (30 Hz)

Accessories

PX901-A: Screw terminal panel with transorb diodes and screw terminals for connecting the analog I/O

PX901-AG: Same as PX901-A with housing for DIN-rail

PX901-ZG: Screw terminal panel with screw terminals for connecting the digital I/O for DIN-rail

ST3009-DZ: 15-pin HD SUB-D female connector on 37-pin SUB-D male connector

ST3009-A: 26-pin HD SUB-D female connector on 37-pin SUB-D male connector

FB3001: Ribbon cable for dig. I/O with 37-pin SUB-D male connector on 3U front bracket
ST010: Standard round cable, shielded, twisted pairs, 2 m

back