Convertisseur résolveur/numérique

Nouveau produit

The resolver-to-digital converter MSX-RDC-17 is a device for supplying and acquiring a resolver. It converts the position value given by the resolver into a digital incremental output signal. The resolution of the incremental encoder output can be defined using the switch on the front side of the MSX-RDC-17.

  • Power supply: nominal voltage 5 V
  • Resolver output/input: Frequency: 10 kHz
  • Resolver connection
  • Signaux de sortie : incrémental A+, A-, B+, B-, Index+, Index-
  • Output type: differential, RS485
  • Résolution : 10/12/14/16 bits

The resolution of the incremental output is set through a switch panel on the front side of the MSX-RDC-17.

Caractéristiques techniques

Caractéristiques techniques

Alimentation en courant
Tension nominale: 5 V

Entrée/sortie résolveur
• Frequency: 10 kHz

Sortie codeur
• Output signals: incremental A+, A-, B+, B-, Index+, Index-
• Output type: differential, RS422
• Resolution: 10-/12-/14-/16-bit

Connecteur pour l’alimentation
Pour l’alimentation en courant, un bloc de jonction à 4 broches est monté sur la partie inférieure du MSX-RDC-17. Les broches de masse et d’alimentation sont connectées à l’intérieur du boîtier. Néanmoins, pour minimiser la circulation de courant sur les bornes, veuillez connecter les quatre broches à l’extérieur !

Commutateur
On the front side of the MSX-RDC-17, a switch panel with three switches is installed. Switches 1 and 2 are used for setting the resolution of the incremental encoder output. Switch 3 allows you to reset the MSX-RDC-17. To do a reset, you have to switch on switch 3 for a short time and then switch it off again. Please do not leave switch 3 switched on permanently, because the MSX-RDC-17 is not functional with this switch position

Connecteur du résolveur
The resolver has to be connected to the 9-pin D-Sub female connector onthe front side of the MSX-RDC-17.

Incremental encoder output
Les signaux du codeur incrémental sont disponibles au connecteur mâle D-Sub à 9 broches du MSX-RDC-17

Signal Index (sortie codeur)
Une impulsion Index est généré lorsque la position angulaire absolue passe par 0.

Utilisation conforme
The resolver-to-digital converter MSX-RDC-17 has to be used as electrical equipment for measurement, control and laboratory pursuant to the standard DIN EN IEC 61010-1. The power supply for the resolver-to-digital converter MSX-RDC-17 must fulfil the requirements of DIN EN IEC 62368-1 and DIN EN 55032 or IEC/CISPR 32 and DIN EN 55024 or IEC/CISPR 24.

Restrictions d’utilisation
The resolver-to-digital converter MSX-RDC-17 must not be used as a safety-related part (SRP).
The resolver-to-digital converter MSX-RDC-17 must not be used for safety-related functions, for example for emergency stop functions.
The resolver-to-digital converter MSX-RDC-17 must not be used in potentially explosive atmospheres.
The resolver-to-digital converter MSX-RDC-17 must not be used as electrical equipment according to the Low Voltage Directive 2014/35/EU.

Limites d’utilisation
All safety information and the instructions on this datasheet must be followed to ensure proper intended use. Uses of the resolver-to-digital converter beyond these specifications are considered as improper use. The manufacturer is not liable for damages resulting from improper use. The resolver-to-digital converter must remain in its anti-static packaging until it is installed. Please do not delete the identification numbers of the resolver-to-digital converter or the warranty claim will be invalid.



GREEN for the new products
ORANGE for products in end of life

HAUT